DUNGS EMx-... - Actuators (US/CA)

[{"filename":"emx_datasheet_us_265471.pdf","text":"Electric Actuators\n\n\n\n\n EMA-…\n\n • Two position, spring return.\n\n Karl Dungs Inc. Actuators are de- 90° & 180° Clockwise rotation when\n signed to operate dampers, butterfly power is applied, actuator returns\n valves and similar devices. Models counter-clockwise to 0° on power\n are available for a variety of torques interruption.\n from 16 in. lb. to 450 in. lb. and con-\n EMA-4..\n trol methods including two-position, EMP-…\n position proportioning with slide-wire\n feedback, potentiometer proportion- • 4..-1 Position Proportioning 100 Ohm\n ing and current-to-position propor- Slidewire Feeback.\n tioning.\n 90° (180° optional with 180° slidewire\n All models are UL listed. kit). Rotation when power is applied.\n\n • 4..-2 Potentiometer Slaved Propor-\n EMP-4..-1 tioning, 100-1000 Ohm, Slidewire\n Feedback\n\n 90° (180° optional with 180° slidewire\n kit). Rotation when power is applied.\n\n • 4..-5 Proportioning, 4-20 mA Input;\n NEMA Type 4\n\n 90° (180° optional with 180° slidewire\n EMP-4..-2 kit). Clockwise rotation (reversible)\n when power is applied.\n\n • -9... Position Proportioning 100 Ohm\n Slidewire Feedback.\n\n 90° (180° optional with 180° slidewire\n kit). Rotation when power is applied.\n\n\n\n\n Actuator Sales Brochure • P/N 265471 • Edition 2024.04\n Optional 4 - 20 mA Input with CP 8391-\n EMP-4..-5 703 (part # 43118-6)\n\n\n\n\n1…2 EMP-9...\n\f Electric Actuators\n\n\n\n\nModel Part No. Voltage Stroke Timing (sec.) Torque Electrical Includes Ambient Temp (F)\n Amps Aux. Switch (3) Crank Arm Min. Max.\n\nTwo Position\nEMA-405-0-0-1 269227 110-120 VAC @ 60 Hz 180 20 16 0.40 No Yes -40 +135\nEMA-405-1-0-1 269228 110-120 VAC @ 60 Hz 90 10 16 0.40 No Yes -40 +135\nEMA-418-2 269242 110-120 VAC @ 60 Hz 90 10 60 0.90 No Yes -40 +135\nPosition proportioning with 100 Ohm slidewire feedback\nEMP-423-1 (1) 269235 110-120 VAC @ 60 Hz 90 12 60 0.65 Yes Yes -40 +135\nEMP-424-1 (1) 269222 110-120 VAC @ 60 Hz 90 12 (2) 60 0.65 Yes Yes -40 +135\nEMP-453-1 (1) 267207 110-120 VAC @ 60 Hz 90 40 220 0.65 Yes Yes -40 +135\nEMP-454-1 (1) 269225 110-120 VAC @ 60 Hz 90 40 (2) 220 0.65 Yes Yes -40 +135\nEMP-9430 267245 110-120 VAC @ 60 Hz 90 20 550 1.80 Yes No (4) -40 +130\nEMP-9630 269246 110-120 VAC @ 60 Hz 90 33 1100 1.80 Yes No (4) -40 +130\nEMP-9830 269243 110-120 VAC @ 60 Hz 90 57 1300 1.80 Yes No (4) -40 +130\nPotentiometer slaved proportioning with 100 - 1000 Ohm slidewire feedback\nEMP-423-2 267228 110-120 VAC @ 60 Hz 90 12 60 0.65 Yes Yes -30 +135\nEMP-424-2 267204 110-120 VAC @ 60 Hz 90 12 (2) 60 0.65 Yes Yes -30 +135\nEMP-454-2 267212 110-120 VAC @ 60 Hz 90 40 (2) 220 0.65 Yes Yes -30 +135\nProportioning, 4 - 20 mA input\nEMP-423-5 267229 110-120 VAC @ 60 Hz 90 12 60 0.65 Yes Yes -40 +135\nEMP-424-5 269223 110-120 VAC @ 60 Hz 90 12 (2) 60 0.65 Yes Yes -40 +135\nEMP-453-5 269224 110-120 VAC @ 60 Hz 90 40 220 0.65 Yes Yes -40 +135\nEMP-454-5 269226 110-120 VAC @ 60 Hz 90 40 (2) 220 0.65 Yes Yes -40 +135\n(1) Can be used a two position if internal slidewire is not connected\n(2) Timing can be increased (slower rotation) up to approximently ten times this rating by turning a slotted adjustment screw locatedon the outside of the case.\n(3) SPDT switch may be set to operate at any point in the stroke (Ratings 120 VAC, 5.8 A inductive 12 A non-inductive.)\n(4) Requires 3/4 crankarm (Part# 43202)\nModels suitable for 50 Hz available upon special request\n\n\n\n Dimension in Inches Shipping W\n Model\n W L H Shaft Dia. Weigh\n\nEMA-405-0-0-1\nEMA-405-1-0-1 4 5 5/8 5 - 3/4 1/2 8 .lbs\nEMA-418-2\n\nEMP-423-1\nEMP-424-1\n 4 5 - 3/8 7 1/2 8 .lbs H\nEMP-453-1\nEMP-454-1\n\nEMP-423-2 W\nEMP-424-2 4* 5 - 3/8 7 1/2 8 .lbs\nEMP-454-2\n Mounting holes (3)\nEMP-423-5 9/32” (7.14 mm) Dia.\nEMP-424-5\n 4** 5 - 3/8 7 1/2 8 .lbs\nEMP-453-5\nEMP-454-5\n\nEMP-9430\n H\nEMP-9630 9 - 1/2 10 - 1/2 9 - 9/16 3/4 8 .lbs\nEMP-9830\n\n* For EMP-2 add 1 1/2” to width to accommodate side box\n** For EMP-5 add 2” to width to accommodate side box\n\n Shaft Dia.\n 1/2” (13 mm)\n\n\n\n\nKarl Dungs, Inc. Karl Dungs GmbH & Co. KG\n3890 Pheasant Ridge Drive NE P.O. Box 12 29\nSuite 150 D-73602 Schorndorf, Germany\nBlaine, MN 55449, U.S.A. Phone +49 7181-804-0\nPhone 763 582-1700 Fax +49 7181-804-166\nFax 763 582-1799 e-mail info@dungs.com\ne-mail info@karldungsusa.com Internet http://www.dungs.com\nInternet http://www.dungs.com/usa/ 2…2"}]