Fireye 48PT2 Series IR Flame Scanners. It is designed for use on D-Series, FlameMonitor

[{"filename":"SC-103-Flame_Scanner_48PT2_Flame_Rod_69ND1_English_2018-06-07.pdf","text":"®\n\n SC-103\n JUNE 7, 2018\n\n\n ®\n FIREYE\n 48PT1\n (Obsolete)\n FLAME SCANNERS\n INFRARED: 48PT1, 3G-OTH-02798 and 3G-OTH-02798-CEX\n FLAME ROD: 69ND1\n 3G-OTH-02798 For UV Self-Check Scanners use SC-101\n For Hazardous Locations or NEMA 4X Scanners use SC-106\n For Non Self-Check UV Scanners use SC-102\n\n 69ND1\n\n APPROVED\n\n\n\n\nDESCRIPTION\n The 3G-OTH-02798 scanner comes with cables rated for Tray Cable - Exposed Run (TC-ER) and complies\n with the crush and impact requirements of the standard for metal clad cable, UL 1569.\n 48PT1 (Obsolete)\n The 48PT1 lead sulfide infrared scanner contains a high impedance detector and is designed to be\n used only on P-Series controls.\n\n 3G-OTH-02798\n The 3G-OTH-02798 lead sulfide infrared scanner contains a low impedance detector and is designed to detect\n low flicker frequency IR signals from gas and oil flames. It is designed for use on D-Series, Flame-\n Monitor, FlameWorx, MicroM and Burnerlogix controls.\n\n 3G-OTH-02798-CEX\n The 3G-OTH-02798-CEX is a 3G-OTH-02798 mounted in a ATEX compliant housing for environments requiring the\n rating of Exd IIC T6 ATEX hazardous location.\n\n 69ND1\n The 69ND1 flame rod is made of high temperature resistant metal and can be used only to detect gas\n flames. The rods come in 12, 18 and 24 inch lengths.\n\n\n CAUTION: Fireye scanners are for use only with Fireye controls. Do not connect Fireye\n scanners with controls not manufactured by FIREYE.\n\n CAUTION: If component checking is required during burner operation for constantly fired\n burners, utilize the infrared flame scanner (3G-OTH-02798) with associated AutoCheck amplifier. For\n Flame-Monitor systems use the E1R1, E1R3 or E1R2 and for MicroM systems use the MEIR1\n or MEIR4.\n Warning- all installation, service and troubleshooting of Fireye products must be performed\n by a qualified technician.\n\n\n 1\n\f \n\n\n\n\n 13/16 HEX 2 3/8\n 5.0 (127) (20.6) (60.3) ”L”\n 2.504 1” DIA. 2 1/2 2 3/8\n (63.6) (25.4) (63.5) (60.3)\n 15/16 HEX\n (23.8) 1/2\n (12.7)\n 1 1/4 DIA.\n (31.8)\n\n\n.385 DIA. (8.7) HEAT INSULATOR\n 1/2-14 1/2-14 NPT\nTC-ER CABLE\n 1/2-14 TAPERED ”L” LENGTH AS SPECIFIED: 12”, 18”, 24” (304.8, 457.2, 609.6)\n STRAIGHT PIPE THD PIPE THD\n\n\n 3G-OTH-02798-1000 SERIES INFRARED SCANNER 69ND1 FLAME ROD\n\n\n\n 3.96 (100.5)\n 1.02” 2 1/2\n 1.46 DIA. (63.5)\n (37.1) 13/32 (10)\n\n\n 1 1/4 DIA.\n (31.8)\n 2.13\n (54)\n HEAT INSULATOR\n 1/2-14\n 1/2-1 TAPERED\n STRAIGHT PIPE THD PIPE THD\n\n .385 DIA. (8.7) TC-ER CABLE\n\n\n 3G-OTH-02798-9000 SERIES INFRARED SCANNER\n\n\n\n Scanner Model Type Approx. Volts Approx. Resistance* Ambient Temp. Limits\n Across Cell of Cell\n 48PT1 Infrared 125VDC 1.5 Meg. ohms 140°F/ 60°C, -40°\n 3G-OTH-02798 Infrared 7-15VDC 20K - 80K ohms 140°F / 60°C, -40°\n 3G-OTH-02798-CEX\n 69ND1 Flame Rod 280-305 VAC Infinite Tip 2460°F\n 1500°F/816°C, -40°\n * Resistance measured with 20K Ohms/ Volt Meter\n For proper Flame Signal Voltage see technical bulletin for the appropriate control.\n 3G-OTH-02798 scanners comply with NEMA 4X\n\n PART NUMBER DESCRIPTION USE WITH\n 48PT1-1003 IR Straight Head 8 feet (2440mm) leads\n 48PT1-1007 IR Straight Head 4 feet (1220mm) Leads\n 48PT1-9003 IR 90 deg. Head 8 ft. (2440mm) Leads P-Series\n 48PT1-9007 IR 90 deg. Head 4 ft. (1220mm) Leads\n 48PT1-9007W - 9007 Water Repellent\n 3G-OTH-02798-1003 IR Straight Head 8 feet (2440mm) leads\n 3G-OTH-02798-1007 IR Straight Head 4 feet (1220mm) Leads C & D Series, MicroM,\n 3G-OTH-02798-9003 IR 90 deg. Head 8 ft. (2440mm) Leads FLAME-MONITOR,\n 3G-OTH-02798-9007 IR 90 deg. Head 4 ft. (1220mm) Leads BurnerLogix\n 3G-OTH-02798-CEX IR Straight Head, 1/2” NPT inlet\n 35-69 Heat Insulator for 48PT Scanners\n 69ND1-1000K4 Flame Rod 12 inches (305mm) 1/2 in. mount\n P, C, D, M-Series, MicroM,\n 69ND1-1000K6 Flame Rod 18 inch (460mm) 1/2 in. mount)\n MB Systems, BurnerLogix,\n 69ND1-1000K8 Flame Rod 24 inches (710mm) 1/2 in. mount\n FLAME-MONITOR\n\n For information on the 45UV scanners, see Bulletin SC-101.\n For information on the 55UV scanners, see Bulletin SC-106.\n For information on the UV1A, UV2, and UV8A scanners, see Bulletin SC-102.\n\n\n2\n\f ®\n\n\n\n\nSCANNER MAINTENANCE\n 48PT1 and 3G-OTH-02798, 3G-OTH-02798-CEX Infrared Scanners and 69ND1 Flame Rods\n The viewing area of the scanner must be kept clean. Even a small amount of contamination will\n reduce the flame signal reaching the detector by a measurable amount. Wipe the viewing area rou-\n tinely using a soft cloth dampened with concentrated detergent.\n Type 48PT1 scanner includes a replaceable #4-128-1 cell\n Type 3G-OTH-02798, 3G-OTH-02798-CEX scanner includes a replaceable #4-263-1 Firetron cell.\n Type 69ND1 Flame Rod. Rods should be routinely replaced as they…