Interpump C14 LP 132X85X8 Buyer's Guide: High-Pressure Pump Selection for Singapore

The Interpump INTERPUMP C14 LP 132X85X8 is a low-pressure pump variant in Interpump's industrial high-pressure pump range, identified by its 132 x 85 x 8 mm interface envelope. In Singapore it is typically sourced as a replacement or OEM component for pressure washers, marine washdown and precision-manufacturing wash systems running on 230 V / 50 Hz single-phase or 400 V three-phase supply.

What is the Interpump INTERPUMP C14 LP 132X85X8?

A C14 LP pump is a low-pressure (LP) member of Interpump's C-series high-pressure pump family, distinguished by its 132 x 85 x 8 mm mounting and port interface. Interpump is an Italian OEM whose pumps are widely used in pressure washers, industrial cleaning and process water systems.

The "LP" designation signals a lower-pressure duty point than the standard high-pressure C-series pumps, making it suitable for pre-wash, rinse and transfer stages rather than the final high-pressure cut. Buyers should always confirm the exact shaft type, flange pattern and valve orientation against the pump nameplate before ordering.

How does an Interpump high-pressure pump work?

Interpump high-pressure pumps use a crankshaft-driven plunger or piston arrangement to pressurise water. A motor — electric or petrol — turns the crankshaft, which drives the plungers inside ceramic or hardened-steel cylinders. Inlet valves draw water in on the downstroke; outlet valves discharge it on the upstroke.

Flow and pressure are set by the plunger diameter, crankshaft stroke and rotational speed (rpm). Interpump pumps in the 3G Electric Singapore catalogue run at 1450–3400 rpm, delivering 9–21 L/min at 103–275 bar depending on model.

Interpump pump specification table

The table below summarises the Interpump pump models currently stocked by 3G Electric in Singapore. All values are taken from Interpump datasheets.

Which Interpump pump type suits your Singapore application?

Interpump pumps fall into three broad families relevant to Singapore buyers: the TT series (compact, petrol-engine or gas-driven, 150 bar), the WW series (low-flow, low-pressure washdown), and the E-series (higher-pressure industrial duty up to 275 bar).

In Singapore, the most common applications are:

• Marine and offshore washdown — salt-laden humid air demands corrosion-resistant housings and regular seal inspection; TT and E-series pumps are common.
• Precision manufacturing — coolant and parts-wash systems in Jurong and Tuas plants typically use E2C or E3B pumps at 200–250 bar.
• F&B and pharma plants — CIP (clean-in-place) and rinse stages often use lower-pressure LP variants such as the C14 LP.
• Pressure washers and mobile cleaning — TT1512 petrol-engine pumps suit site work where 230 V supply is unavailable.

How to select the right Interpump pump

1. Match pressure to duty. Confirm the required discharge pressure in bar (or MPa/psi). LP stages typically run below 150 bar; high-pressure cut stages run 200–275 bar.
2. Size flow to nozzle and cycle time. Flow in L/min must match the nozzle orifice and the required cleaning rate. Interpump models in stock range from 9 L/min to 21 L/min.
3. Confirm shaft, flange and valve orientation. The C14 LP 132X85X8 interface (132 x 85 x 8 mm) must match your existing mounting. Check male shaft (key) vs hollow shaft, and left vs right valve orientation.
4. Check power supply. Singapore uses 230 V / 50 Hz single-phase and 400 V / 50 Hz three-phase. Confirm motor rating in kW matches available supply and starter.
5. Consider environment. Humid tropical conditions accelerate corrosion; specify appropriate seals and inspect regularly. For outdoor or washdown areas, consider IP-rated motor enclosures.
6. Verify duty cycle. Continuous industrial duty requires a pump rated for the rpm and thermal load; intermittent cleaning allows a lighter pump.

Interpump pump comparison ladder: light duty to heavy duty

The table below arranges five in-stock Interpump pumps from light duty to heavy duty, so you can see where the C14 LP class sits relative to alternatives.

Step up the ladder when your nozzle pressure demand exceeds 150 bar, when flow must exceed 12 L/min for cycle time, or when duty cycle moves from intermittent to continuous. Step down when the application is a pre-wash or rinse stage where 150 bar is sufficient — a lighter pump reduces power draw and wear.

Why source Interpump pumps from 3G Electric in Singapore?

3G Electric stocks over 4,007 products across 14 industrial departments — from pumps and combustion to controls, instrumentation and power transmission. We are a distributor and supplier, not just a catalogue: our team interprets your demand, confirms the correct Interpump variant, and delivers from Singapore stock.

With 35+ years of experience and specialist depth in pumps, combustion and controls, we support Singapore buyers in marine/offshore, precision manufacturing, F&B and pharma. We also supply complementary brands such as Schneider, ABB, Siemens, SKF, Festo and Fluke for the surrounding electrical and control scope.

According to Interpump Group S.p.A. TT1511 datasheet, 2026: "TT1511 is a compact industrial gear pump for high-pressure gas applications, delivering 11 L/min at 150 bar."

Frequently asked questions

What is the Interpump INTERPUMP C14 LP 132X85X8 used for?
The C14 LP is a low-pressure pump variant used in pre-wash, rinse and transfer stages of pressure-washing and process-water systems. Its 132 x 85 x 8 mm interface identifies the mounting envelope. Confirm shaft and valve orientation against your existing pump before ordering.

How do I choose between an LP and a high-pressure Interpump pump?
Match discharge pressure to the duty: LP stages typically run below 150 bar, while high-pressure cut stages run 200–275 bar. If your nozzle and cycle time require more than 150 bar, step up to an E-series pump such as the E2C2015 or E3B2515.

What voltage do Interpump pumps use in Singapore?
Singapore supply is 230 V / 50 Hz single-phase and 400 V / 50 Hz three-phase. Confirm the motor rating in kW matches your available supply and starter. Petrol-engine models such as the TT1512 are used where mains power is unavailable.

Where can I buy Interpump pumps in Singapore?
3G Electric supplies Interpump pumps from Singapore stock, with technical support to confirm the correct variant. Contact us with your pump nameplate details, required flow (L/min) and pressure (bar) for a quote.

How fast is delivery in Singapore?
3G Electric delivers from Singapore stock, so in-stock Interpump pumps are typically dispatched quickly. Lead time depends on stock status and variant; confirm at the time of enquiry.

Do I need EMA licensing or WSH compliance for a pump installation?
Electrical installations in Singapore should comply with EMA requirements and WSH regulations for the workplace. For fixed installations, engage a licensed electrical worker. 3G Electric can advise on the pump scope; site electrical compliance remains the installer's responsibility.

Key takeaways

• The Interpump INTERPUMP C14 LP 132X85X8 is a low-pressure pump variant identified by its 132 x 85 x 8 mm interface envelope.
• Interpump pumps in the 3G Electric Singapore range span 2.57–7.13 kW, 9–21 L/min and 103–275 bar.
• Always confirm shaft type, flange pattern and valve orientation before ordering a replacement.
• Singapore supply is 230 V / 50 Hz single-phase or 400 V / 50 Hz three-phase; humid conditions demand corrosion-aware selection.
• 3G Electric stocks 4,007+ products across 14 departments with specialist depth in pumps, combustion and controls.

Contact 3G Electric for Interpump pump quotes, sizing assistance and technical support in Singapore. Share your pump nameplate, required flow (L/min) and pressure (bar), and we will confirm the correct variant from stock.