P5551 / P/N 3885659 Pointer Remover / Punch: International Buyer's Guide to Punching & Extraction Tools
Table of Contentsexpand_more
The P5551 / P/N 3885659 Pointer Remover / Punch is best understood as a workshop punch-and-extraction tool: a hardened hollow arch punch for cutting clean holes in gaskets, leather, rubber and soft metals, or a dedicated puller for removing seized injectors. International buyers should match hole diameter, taper length and overall length to the material and application before ordering.
What is a P5551 / P/N 3885659 Pointer Remover / Punch?
A P5551 / P/N 3885659 Pointer Remover / Punch is a hand-held workshop tool used either to punch precise holes in soft sheet materials or to extract a stuck component such as a fuel injector. In the 3G Electric catalog, this category is represented by GENERAL and GENERAL TOOLS hollow arch punches and MILTON injector pullers.
GENERAL and GENERAL TOOLS arch punches are hollow, tapered cutters — typically 4 in to 5 in overall length with a 9/10 in to 1 in taper — that shear a clean hole through gaskets, leather, canvas, rubber, plastics and thin metals. MILTON injector pullers are steel or aluminium extraction tools for Ford, Lincoln and diesel engine service.
How does a hollow arch punch work?
A hollow arch punch works by concentrating hand or press force through a tapered, hollow cutting edge. The taper (typically 9/10 in to 1 in on GENERAL and GENERAL TOOLS models) guides the punch into the material, while the hollow bore lets the slug exit cleanly so the hole stays round or hexagonal.
Because the cutting edge is hollow, the punch can be used on gaskets, leather, rubber, canvas, plastics and soft metals without tearing the surrounding material. Hex-shaped variants such as the GENERAL TOOLS hexagon arch punches are used where a hex opening is required for fasteners or fittings.
Which type suits your application?
Choose a round hollow arch punch for gasket, leather, rubber and plastics work; choose a hexagon arch punch when the finished hole must accept a hex fastener or fitting; choose an injector puller when the job is removal rather than cutting.
- Gasket and seal making: round hollow arch punches in 1/4 in and up diameters.
- Hex openings in sheet metal: hexagon arch punches with 1 in taper and 4-1/2 in to 5 in overall length.
- Upholstery, canvas and leather: 1 in diameter hollow arch punches with 5 in overall length.
- Ford / Lincoln / diesel injector service: MILTON injector pullers and remover kits.
Spec table: representative P5551 / P/N 3885659 Pointer Remover / Punch options
| Tool type | Hole / extraction size | Overall length | Taper length | Typical material |
|---|---|---|---|---|
| GENERAL 7-piece hollow arch punch set | From 1/4 in SAE diameters | 4 in | 9/10 in to 49/50 in | Gaskets, leather, rubber, soft metals |
| GENERAL TOOLS hexagon arch punch | Hex, SAE | 5 in | 1 in | Gaskets, leather, thin metals |
| GENERAL TOOLS hollow arch punch | 1 in diameter | 5 in | 1 in | Leather, canvas, rubber, plastics |
| GENERAL TOOLS hexagon arch punch (sheet metal) | Hex, SAE | 4-1/2 in | 1 in | Sheet metal |
| MILTON injector puller (Ford/Lincoln) | 1 in length adapter | — | — | Aluminium, red anodized |
Selection criteria: how to choose
- Hole geometry: round for gaskets and seals, hex for fastener openings.
- Hole diameter: confirm SAE size — the GENERAL set starts at 1/4 in; single punches go up to 1 in.
- Overall length: 4 in to 4-1/2 in for compact work; 5 in for reach and leverage.
- Taper length: 9/10 in to 1 in taper balances penetration and edge strength.
- Material thickness: thin metals need hex or arch punches rated for sheet metal; soft materials accept standard hollow punches.
- Extraction vs cutting: if the task is removing an injector, choose a MILTON puller kit rather than a punch.
- Export and voltage context: hand tools are voltage-independent; where kits include powered accessories, confirm 50 Hz / 60 Hz compatibility for your market.
Product selection ladder
| Level | Product | Best for | Key spec |
|---|---|---|---|
| Entry / kit | GENERAL 1271ST 7-Piece Hollow Arch Punch Set | General gasket, leather and rubber work | 1/4 in and up SAE; 4 in overall; 9/10 in to 49/50 in taper |
| Single round punch | GENERAL TOOLS 1 in Hollow Arch Punch | Upholstery, canvas, rubber, plastics | 1 in diameter; 5 in overall; 1 in taper |
| Hex punch | GENERAL TOOLS Hexagon Arch Punch | Hex openings in gaskets and thin metals | Hex SAE; 5 in overall; 1 in taper |
| Hex punch (sheet metal) | GENERAL TOOLS Hexagon Arch Punch for Sheet Metal | Metalworking and fabrication | Hex SAE; 4-1/2 in overall; 1 in taper |
| Extraction | MILTON PowerPull Fuel Injector Puller Kit | Diesel and Ford injector service | Steel; yellow; includes PowerPull kit |
Step up the ladder when the material gets harder or the job shifts from cutting to extraction. Start with the GENERAL 7-piece set for mixed gasket work; move to a dedicated 1 in or hex punch when a single size dominates; and switch to a MILTON puller kit when the task is injector removal rather than hole cutting.
Why source from 3G Electric?
3G Electric stocks 12 products in this category and supplies across 14 industrial departments — from machining and electrical to pneumatics, hydraulics and maintenance tooling. With 35+ years of experience, we interpret the demand, source the right tool and quote it with export documentation experience for International buyers.
Our specialist depth in combustion, pumps and controls is a trust anchor, not a limit: we also supply GENERAL, GENERAL TOOLS, MILTON and OTC tooling alongside brands such as Schneider, ABB, Siemens, SKF, Festo and Fluke. Supply is incoterms-neutral, with cross-market voltage and frequency variants handled on request.
Frequently asked questions
What is a P5551 / P/N 3885659 Pointer Remover / Punch used for?
It is used to cut clean holes in gaskets, leather, rubber, canvas, plastics and soft metals, or to extract stuck injectors. GENERAL and GENERAL TOOLS hollow arch punches cover the cutting role; MILTON injector pullers cover the extraction role.
How do I choose between a round and hex arch punch?
Choose round for gaskets, seals and leather where a circular opening is needed. Choose hex when the finished hole must accept a hex fastener or fitting — GENERAL TOOLS hexagon arch punches are available in 4-1/2 in and 5 in overall lengths with 1 in taper.
What sizes are available in the GENERAL arch punch range?
The GENERAL 7-piece set starts at 1/4 in SAE diameters with a 4 in overall length and 9/10 in to 49/50 in taper. Single GENERAL TOOLS punches include a 1 in diameter hollow punch and hexagon variants with 1 in taper.
Can I order P5551 / P/N 3885659 Pointer Remover / Punch for delivery outside the US?
Yes. 3G Electric supplies International buyers with incoterms-neutral quotes and export documentation experience. Lead times depend on stock and destination; contact us for a current quote in USD.
Do these tools need 50 Hz or 60 Hz power?
No — hollow arch punches and hand injector pullers are manual tools and are voltage- and frequency-independent. Where a kit includes powered accessories, confirm 50 Hz / 60 Hz compatibility for your market before ordering.
Where can I buy GENERAL and MILTON tools in International markets?
3G Electric stocks GENERAL, GENERAL TOOLS, MILTON and OTC tooling and quotes International orders in USD. Contact us with the hole size, material and application for a sizing recommendation and quote.
Key takeaways
- The P5551 / P/N 3885659 Pointer Remover / Punch category covers hollow arch punches and injector pullers.
- Match hole geometry (round vs hex), diameter (1/4 in to 1 in) and overall length (4 in to 5 in) to the job.
- GENERAL and GENERAL TOOLS cover cutting; MILTON covers Ford, Lincoln and diesel injector extraction.
- 3G Electric supplies International buyers with export documentation experience and USD quotes.
Ready to order? Contact 3G Electric for quotes, sizing assistance and technical support on P5551 / P/N 3885659 Pointer Remover / Punch tools and the wider GENERAL, GENERAL TOOLS and MILTON range.
