Fireye Phoenix Series 2 85UV & 85IR Flame Scanners

[{"filename":"MF-00-2-3000-0-021-A-Phoenix_Flame_Scanners_English_2023-12-13.pdf","text":"Phoenix Series 2\nFlame Scanners\n\nIntegrated Flame Scanner\n85UVF / 85IRF\nMicroprocessor flame scanner with solid-\nstate infrared (IR) or ultraviolet (UV) sensors\n\nThe Fireye Phoenix Series 2 type 85UVF/IRF flame\nscanners are microprocessor-based devices utilizing a\nsolid-state flame detection sensor. The flame scanners\nincorporate an internal flame relay with automatically set\nON/OFF thresholds, thereby eliminating the need for a\nremote flame amplifier or flame switch.\n\nThe Phoenix scanners detect the amplitude of the\nmodulations (the flame “flicker”) that occur within the\ntargeted flame, over a wide frequency. During the scanner\nsetup procedure, the amplitudes of the target flame are\nautomatically stored by the flame scanner, together with\noptimum ON/OFF criteria. The appropriate sensor gain is\nautomatically selected. Phoenix scanners incorporate full\nself-diagnostics and electronic self-checking.\n\nFeatures\n • Solid state dual UV or IR sensors\n • Flame relay\n • Fault relay\n • 4-20mA outputs\n • 8-pin electrical quickdisconnect (QD)\n • Auto or manual configuration\n • SIL 3 certified\n\nOptions\n • K3 option, increased UV range upto 500nm\n • Remote communication (Remote programming)\n • ATEX / IECEx ExdIIC T6 versions\n • Marine grade stainless steel versions\n • Fiber-optic compatible\n\nTypical Applications\n • Duct Burners\n • Industrial Gas Burners\n • Refinery Applications\n • Low NOx Burners\n • Waste Gas Units\n • Incinerators\n\n\n\nfireye.com\n\fPhoenix Series 2\nFlame Scanners\nSpecifications\n MECHANICAL ELECTRICAL\n Cast aluminum with gray polyester Minimum (all models): 10 mA @ 5 Vdc\n Housing Material\n powder coat finish Maximum (Series 4E-1WINC models\n 5.9 lbs. (2.69kg), 13.2 lbs. (5.98kg) “CEX” Contact Rating only): 1 A @ 30 Vdc, 1 A @ 50 Vdc\n Housing Weight Maximum (all other models): 1 A @ 30\n models, flange additional\n Vdc, 1 A @ 230 VAC\n Environmental NEMA 4X, IP66\n Optically isolated 4-20mA dc current,\n 85XXF1A-1QD, 85XXF1A-2QD, 85UF- Analog Output referenced to 24 Vdc common, maximum\n F1A-XQDK3, 85XXF4A-XQDWR, 3G-OTH-02852- connected load 750 ohms\n F4A-XQDK3WR : Class I Div 2, Groups A,\n Area Classification B, C, D; Class II Div 2, Groups F & G Multiple LED indication for flame signal\n 85XXF1-1CEX, 85UVF1-1CEX-K3, Operator Interface strength, flame relay, ready, target,\n 85XXF1-1CEXSS, 85UVF1-1CEXK3SS : background select and fault codes\n Ex d IIC T6\n CABLE SPECIFICATION\n Requires one of two threaded mounting\n Mounting Multi-core 8 conductor (color coded), 18-\n flanges, ordered separately (see below)\n AWG, with foil wrap and overall braided\n Contains an integral heat-insulating\n shield and drain wire; PLTC-ER rating\n Mounting Flanges female thread insert (heat insulating nipple\n Cable jacket: PVC/black (flame-retardant,\n not required)\n low smoke, zero halogen)\n P/N 59-546\n P/N 60-2919-1 1” NPT female pipe mount with 3/8” NPT Temperature rating: -40°F to +221°F\n female cooling air connection (-40°C to +105°C)\n Nominal outer diameter: 0.52 in. (13.2mm)\n 1” BSP female pipe mount with 3/8” BSP\n P/N 60-2919-2 Maximum outer diameter: 0.56 in. (14.2mm)\n female cooling air connection\n Maximum cable length: 1,000 ft. (305m)\n Mounting Flange\n 0.62 lbs (0.28kg)\n Weight\n Dimensions\n COOLING/PURGE AIR REQUIREMENTS\n Source Clean, dry, cool\n 4 SCFM (113 l/min) at 3/8” threaded\n mounting flange, or 1” “Y” fitting, mounted\n on scanner sight pipe. Temperature near\n Volume\n the upper limit of the scanner operating\n range and/or use with dirty/dusty fuels\n may require up to 15 SCFM (425 l/min)\n Temperature Rating -40°F to +150°F (-40°C to +65°C)\n 0% to 95% relative humidity, non-\n Humidity\n condensing\n\n ELECTRICAL\n 24 Vdc, +10%,\n Input Power\n -15% supply current 0.25 A, 6.0 V A\n 8-pin screw-type quick-disconnect (non-\n Electrical Connection\n CEX). CEX models have terminal blocks\n Flame Relay Ouput SPST (N.O.)\n\nFor more information, please contact your local Fireye Distributor.\nfireye.com\nMF-00-2-3000-0-021-A (2023/12)\nAll trademarks and service marks referred herein are property of their respective owners.\n©2023 Fireye. All Rights Reserved.\n\n Join us on"}]