Datasheet Content
[{"filename":"CU-103-Scanner_Insulating_Jacket_English_2015-07-07.pdf","text":"®\n\n CU-103\n JULY 9, 2015\n\n\n\n\n Scanner Insulating Jacket\n P/N 97-1047, 97-1048\n P/N 97-1051, 97-1058\n P/N 97-1067, 97-1069\n P/N 97-1087, 97-1104\n P/N 97-1109\n\n Vortex-tube Cooler Kit\n P/N 60-2720\n\nAPPLICATION\n In high ambient temperature applications, cooling air applied to the scanner’s 3/8” port may be\n unable to maintain the scanner’s temperature below published limits. An effective solution may be to\n install the scanner in an insulating jacket, and air purge the space between the jacket and the scanner.\n Vortex-Tube Cooler Kit, P/N 60-2720, is used to generate and flow chilled air between the jacket and\n scanner. The actual cooling effect will be dependent upon the pressure and temperature of the com-\n pressed air supplied to the vortex-tube.\n\n\nINSULATING JACKETS\n The flexible quilted jacket wraps around the scanner and is secured with hoop & loop seam fasten-\n ers. Holes are provided for scanner cable entry, 1\" sight-pipe entry, and vortex-tube cooling air entry.\n A flap on the rear of the jacket allows access to view the back of the scanners where required.\n\nFIGURE 1. 97-1047 (SHOWN WITH 45FS1 FLAME SCANNER)\n\n\n\n\n 1\n\f \n\n\n\n\nINSULATING JACKET MATERIAL SPECIFICATION\n External Covering: SIL #1700\n Silicone rubber-impregnated fiberglass fabric\n Oil and chemical resistant\n Flame resistant\n Temperature resistance: -65°F (-54°C), +500°F(+260°C)\n\n\n Internal Insulation: ACTMAT 1200 Insulation, 1\" thick\n Textile glass fiber, asbestos free\n Non-combustible, non-toxic\n\n INSULATING JACKET APPLICATIONS\n\n PART SCANNER APPLICATION JACKET DIMENSIONS SHIPPING\n NUMBER (Approximate) WEIGHT\n\n 97-1047 Fits all 45UV5, 45RM, 45FS1, 45UVFS1 13 ½\" (343mm) long x 2.7 lbs. (1.2 kg)\n (except EX and CEX models) 6 ½\" (165mm) diameter\n\n 97-1048 Fits all 95IR, 95UV, 95DS InSight I scanners 12\" (305mm) long x 2.5 lbs. (1.1 kg)\n (except CEX models) 6 ½\" (165mm) diameter\n\n 97-1051 Fits all 55UV5, 65UV5, and C9501 through C9707 9\" (229mm) long x 2.8 lbs. (1.3 kg)\n (except C9506 and C9508) 7\" (178mm) wide and deep\n\n 97-1058 Fits CEX models of 45, 85, and 95-Series InSight I scanners 15\" (381mm) long x 3.2 lbs. (1.5 kg)\n 7 ½\" (191mm) diameter\n\n 97-1067 Fits all 85UV and 85IR Phoenix 13\" (330mm) long x 2.2 lbs. (1.0 kg)\n 6 ½\" (165mm) diameter\n\n 97-1069 Fits 48PT2-CEX and UV1A-1-CEX 8 3/4\" (222mm) long x\n 5 ½\" (140mm) diameter\n\n 97-1087 Fits 95DSS3 InSight II, standard and CEX models 16 ½\" (419 mm) long x 3.1 lbs. (1.4 kg)\n (all except 95DSS3-1CEXSS and 95DSS3-1CEX-2) 7 ½\" (191 mm) diameter\n\n 97-1104 Fits 105F1-1 Paragon 16\" (406 mm) long x 3.5 lbs. (1.6 kg)\n (all except CEX model) 8 ½\" (216 mm) diameter\n\n 97-1109 Fits 95DSS3-1CEXSS and 95DSS3-1CEX-2 InSight II, and 16\" (406 mm) long x 3.5 lbs. (1.6 kg)\n 105F1-1CEX Paragon 8 ½\" (216 mm) diameter\n\n\n\nVORTEX-TUBE COOLER KIT, P/N 60-2720\n The stainless steel vortex-tube contains no moving parts and operates on ordinary compressed air. It\n is secured to an opening on the side of the insulating blanket with hardware provided in the kit.\n Compressed air is supplied to the 1/4\" NPT male fitting on the side of the tube. The tube separates\n the air into two streams. The “cool” air stream is blown into the space between the insulating jacket\n and the scanner, thereby lowering the scanner’s internal temperature. The “warm” air stream is\n exhausted at the bottom of the tube.\n The vortex-tube lowers the temperature of the compressed air supplied to the tube as shown in the\n table below. The resulting decrease in scanner internal temperature will be slightly less than the drop\n in compressed air temperature.\n\n\n\n\n2\n\f ®\n\n\n\n Nominal temperature drop of compressed air supply at various supply pressures:\n AIR SUPPLY PRESSURE, PSIG 20 40 60 80 100 120\n AIR TEMPERATURE DROP °F (°C) 28 (16) 38 (21) 46 (26) 50 (28) 54 (30) 55 (31)\n\n\n\n Compressed Air Supply Requirements:\n Pressure: 80-110 PSIG optimum, (20 PSIG min.)\n Volume: 10 SCFM (at 100 PSIG)\n Filtration: Clean, dry, filtered to 25 microns or less\n\n Dimensions:\n Length: 7 ½\" (191mm), installed\n Shipping weight: 0.9 lbs. (0.4 kg)\n\n\n\nVORTEX TUBE, KIT ASSEMBLY\n\n\n\n EXHAUST VALVE VORTEX TUBE 3/8\" X 2\" PIPE NIPPLE 3/8\" X 1/2\" HEX BUSHING LOCKING NUT\n\n\n\n\n COOL AIR OUTLET\n WARM AIR 3/8\" NPT (FM)\n EXHAUST FLAT WASHERS\n COMPRESSED\n 1/4\" NPT (M)\n AIR SUPPLY\n 1/4\" NPT (M)\n\n\n 1. Attach the 3/8\" NPT pipe nipple to the vortex-tube cool air outlet.\n 2. Attach the 3/8\" x 1/2\" hex bushing to the pipe nipple.\n 3. Install one flat washer on the hex bushing.\n 4. Insert the hex bushing into the through-hole on the bottom of the insulating jacket.\n 5. Secure the vortex-tube assembly to the insulating jacket with the second flat washer and locking\n nut.\n 6. Wrap the insulating jacket around the installed flame scanner and secure with the with the hook-\n and-loop seam fastener.\n\n Note: The insulating jacket does not allow easy access to the scanner housing cooling air tap.\n It is recommended that this cooling air tap be plugged, and cooling/purge air be connected to\n the scanner sight pipe at a 1\" tee or wye located between the scanner and the burner.\n\n 7. Connect the compressed air supply to the 1/4\" NPT male fitting on the side of the vortex-tube.\n\n Note: Support the compressed air supply line to avoid stress on the insulating jacket.\n\n 8. The temperature of the cool air produced by the vortex tube may be adjusted by the slotted\n Exhaust Valve on the vortex tube tip. The exhaust valve is factory set at 1-turn open. Further\n opening the valve (counter-clockwise) will lower the cool air temperature, but will reduce the\n cool air flow. Further closing the valve (clockwise) will raise the cool air temperature, but will\n increase the cool air flow.\n\n\n\n 3\n\f \n\n\n\n\nNOTICE\n When Fireye products are combined with equipment manufactured by others and/or integrated into\n systems designed or manufactured by others, the Fireye warranty, as stated in its General Terms and\n Conditions of Sale, pertains only to the Fireye products and not to any other equipment or to the com-\n bined system or its overall performance.\n\nWARRANTIES\n FIREYE guarantees for one year from the date of installation or 18 months from date of manufacture\n of its products to replace, or, at its option, to repair any product or part thereof (except lamps, elec-\n tronic tubes and photocells) which is found defective in material or workmanship or which otherwise\n fails to conform to the description of the product on the face of its sales order. THE FOREGOING IS\n IN LIEU OF ALL OTHER WARRANTIES AND FIREYE MAKES NO WARRANTY OF\n MERCHANTABILITY OR ANY OTHER WARRANTY, EXPRESS OR IMPLIED. Except as\n specifically stated in these general terms and conditions of sale, remedies with respect to any product\n or part number manufactured or sold by Fireye shall be limited exclusively to the right to replacement\n or repair as above provided. In no event shall Fireye be liable for consequential or special damages of\n any nature that may arise in connection with such product or part.\n\n\n\n FIREYE…
