DUNGS Ignition Transformers (US/CA)

[{"filename":"ignition-transformers_manual_us_261486.pdf","text":"Ignition Transformer\n Installation Instructions USA CDN\n\n\n\n\n Table of Contents\n Table of Contents . . . . . . . . . . . . . . . . . . . . . . . . Page 1\n Approvals . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Page 1\n Attention . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Page 1\n Specification . . . . . . . . . . . . . . . . . . . . . . . . . . . . Page 2\n Dimensions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Page 3\n Trouble Shooting . . . . . . . . . . . . . . . . . . . . . . . . Page 3\n Installation and Wiring Instructions . . . . . . . . Page 3\n\n\n\n\n Approvals\n CSA Certified:\n Allanson CSA File # L744Z\n CSA 22.2 No. 13\n UL 506\n\n\n\n\n Attention\n The installation and maintenance On completion of installation on\n of this product must be done Safety the Ignition Transofrmer, perform\n under the supervision of an ex-\n perienced and trained specialist.\n first a function test.\n\n Never perform work if gas pres-\n sure or power is applied, or in\n the presence of an open flame.\n O.K.\n\n\n\n\n MC • Karl Dungs, Inc. • Ignition Transformer • Edition 2024.04 • P/N 261486 • Rev. -0\n Please read the instruction be- This product is intended for\n fore installing or operating. Keep IFGC installations covered by but not\n the instruction in a safe place. You CSA limited to NFPA 70, NFPA 79,\n find the instruction also at www. UL NFPA 85, NFPA 86, UL 795, CSD-\n dungs.com If these instructions ANSI 1, ANSI Z83.4, ANSI Z83.18, ANSI\n are not heeded, the result may NFPA Z21.13, and CSA B149.3.\n be personal injury or damage to\n property.\n\n\n\n\n Explanation of symbols\n 1, 2, 3 ... = Action\n • = Instruction\n1…3\n\fSpecification\nThis transformer is intended for industrial or commercial heating applications that use a 6000 VAC input spark ignitor to\nignite fuel at a burner. This product is an internally grounded, single pole electrode type ignition transformer.\n\n Electrical Input Rating Available/VA Ambient and Surface Mounting\n 120 VAC/50-60 Hz (+10%; -15%) °F Temperature\n +110\n 240 VAC/60Hz (+10%; -15%) +5 °F to +110 °F (-15 °C to +40 °C)\n 240 VAC/50 Hz (+10%; -15%) +5\n 0\n [V] [A] Amperage\n [Hz] [VA] Operation: 1.5 A input on the pri-\n mary. Inrush current for first 250\n milliseconds:\n 1) 8 A on first start (new out of the box)\n 2) 3 A on every start thereafter.\n\n\n\n\n Shipping Weight Mounting Position\n 10 lbs Any\n\n Grounding Electrical Connection on Primary\n This transformer is a signal elec- Leads with 1/2” opening for locknut.\n trode type and the primary is inter-\n nally grounded. If a separate primary\n ground wire is required, contact Karl\n Dungs for different models.\n\n\n\n\nPart Number Primary Secondary Allanson Input Current Input Current\n Voltage Voltage Type +/- 15 % @ 50 Hz +/- 15 % @ 60 Hz\n267344 120 V / 50 - 60 Hz 6,000 VAC 1092-S 1.60 0.50\n267343 240 V / 60 Hz 6,000 VAC 1112-S 0.60* 0.25\n267342 240 V / 50 Hz 6,000 VAC 1196-S 0.40 0.20*\n*Not recommended for operation at this frequency. The transformer may overheat, which will decrease the transformer‘s life.\n\n\n\n\n MC • Karl Dungs, Inc. • Ignition Transformer • Edition 2024.04 • P/N 261486 • Rev. -0\n\n\n\n\n 2…3\n\f Dimensions\n\n\n\n 1 5/16”\n\n\n\n\n 7/8” Dia\n 5 29/32”\n Knockouts\n 5 7/8” 6 3/4”\n\n\n\n\n Junction Box\n 1 1/4”\n Cover\n 3 7/8” 1/16” 4 7/16”\n\n\n Trouble Shooting\n • Resistance across L1 and L2 should be 2.5 Ohms.\n\n Installation and Wiring Instructions\n • Remove the protective paper on top of the transformer. Do not ground the secondary using a ground\n • Use UL Recognized GTO ignition cable or wire rated for wire. The secondary requires only one wire,\n the continous output voltage of the transformer. which is connected to a spark ignitor.\n • The secondary ignition GTO wire must not exceed 8 ft.\n…