Fireye MicroM Programmer Modules. The Fireye MicroM Series is a compact, microprocessor-based

[{"filename":"MP-5101-MicroM_Programmer_Modules_MEP100_MEP100P_MEP101_MEP102_MEP103_MEP104_MEP105_MEP106_MEP107_MEP108_MEP109_MEP130_MEP141_MEP149_English_2013-04-03.pdf","text":"®\n\n MP-5101\n APRIL 3, 2013\n\n MEP100, MEP100P, MEP101, MEP102,\n MEP103, MEP104, MEP105, MEP106,\n MEP107, MEP108, MEP109,\n MEP130, MEP141 and MEP149\n PROGRAMMER MODULES\n C U L US\n \n FOR USE WITH THE FIREYE® MODULAR\n LISTED APPROVED MicroM™ CONTROL TO BE USED\n WITH MEC120 AND MEC230 CHASSIS\n\nDESCRIPTION\n The Fireye MEP100, MEP100P, MEP101, MEP102, MEP103, MEP104, MEP105, MEP106 MEP107,\n MEP108, ME109, MEP130, MEP141 and MEP149 Programmer Modules are used with the Fireye Modu-\n lar MicroM control. The operational characteristics of the control are determined by the selection of the\n programmer module (e.g. re-light, 2-stage capability, pilot cutoff, etc.). The programmer module incorpo-\n rates a plug-in design for easy installation.\n The advantages of the Micro M are zero dependence on discrete components previously used for timing\n functions. The MicroM, through the use of micro-controller technology, incorporates smart diagnostic\n LED’s, smart reset function for multi-burner applications, optional alpha-numeric display output (ED510)\n and serial communications via a Modbus-RTU.\n Flame Failure Response Time (FFRT) is determined by the selection of the amplifier module. Test jacks\n are also provided on the flame amplifier module to permit flame signal measurement during operation.\n For proper and safe application of this product, you must refer to Fireye bulletin MC-5000 for a detailed\n description of the various programmer modules, including installation instructions, amplifier selection,\n operating sequences for each programmer module, etc.\n\n\n WARNING: Selection of this control for a particular application should be made by a competent\n professional, licensed by a state or other government agency. Inappropriate application of this\n product could result in an unsafe condition hazardous to life and property. Installation should not\n be considered complete until pilot turndown and other appropriate performance tests have been\n successfully completed.\n\n\nPROGRAMMER MODULE SELECTION\n\n\n MicroM Programmer Models\n MEP100 Relight operation, 10 sec. PTFI.\n MEP101 Relight operation, allow flame signal until 60 seconds after interlock closed.\n MEP102 Non-recycle on flame fail, 5 second PTFI.\n MEP103 Fixed 10 second SISP*, 10 second MTFI, re-try once on igniter failure, fixed 30 second post purge.\n MEP104 Non-recycle on flame fail, 10 second PTFI.\n MEP105 Non-recycle on flame fail, lockout on air-flow open with flame present, 10 second PTFI.\n MEP106 Same as MEP100. 12 second pre-purge, added reset from lockout via line voltage.\n MEP107 Same as MEP100. Force 5 minute purge delay after main flame fail.\n MEP108 Immediate ignition and pilot, 15 second PTFI, non-recycle on flame fail. Not FM approved.\n MEP109 Immediate ignition and pilot, 10 second fixed PTFI, 10 second MTFI, intermittent pilot, non-recycle on flame fail.\n MEP100P Relight operation, 10 second PTFI, fixed 15 second post purge.\n MEP130 Relight operation, 30 sec PTFI, no agency approvals\n MEP141 Non-recycle on flame fail, 30 second purge, 5 second fixed PTFI, 8 second pilot stabilization period,\n intermittent pilot, 15 second post purge, prove air open at start.\n MEP149 Non-recycle on flame fail, 30 second purge, 5 second fixed PTFI, 8 second pilot stabilization period,\n intermittent pilot, 90 second post purge, prove air open at start.\n\n *Spark Igniter Sensing Period\n 1\n\f \n\n\n\n\n WARNING: Remove power from the control and remove the control from its wiring base\n before proceeding.\n\n\nINSTALLATION\n The Programmer Modules are used with the The programmer modules are\n Fireye modular MicroM Chassis designed to fit into the proper\n slot only.\n (P/N MEC120, MEC120RC, MEC120R, DO NOT FORCE THEM\n MEC120D and MEC120C for 120VAC and\n MEC230 for 230 VAC). They are installed in\n the chassis by grabbing hold of the programmer\n module by the ridged finger grips on the side\n on the module, aligning the module with the\n guide slots on the opening farthest from the\n transformer, and inserting the module into the\n pin connectors.\n\n\nLOCKOUT CODES\n MSGN DESCRIPTION OP AIRFLOW PTFI FLAME ALARM\n CTRL INTLCK\n DEC HEX\n 6 6 Lockout Line Frequency Noise Detected     \n 7 7 Lockout Flame Fail - PTFI     \n 15 0F Lockout Fault Unknown     \n 16 10 Lockout Amplifier High Count Fail     \n 19 13 Lockout Flame Fail - MTFI     \n 20 14 Lockout False Flame - STANDBY     \n 21 15 Lockout Intrlck Open     \n 22 16 Lockout Intrlck Closed     \n 24 18 Lockout Chassis Opto     \n 37 25 Lockout Flame Fail - AUTO     \n 39 27 Lockout Fuel Valve State Change     \n 54 36 Lockout Check Chassis     \n 55 37 Lockout Check Programmer     \n 56 38 Lockout Check Amplifier     \n 58 3A Lockout Amplifier Auto Check Fail     \n 59 3B Lockout Check BLOWN FUSE     \n 76 4C Lockout Check Scanner     \n\n = NOT LIGHTED\n = LIGHTED\n = FLASHING\nAll MicroM chassis are shipped with a convenient peel off label that can be applied to any surface (inside cover) for future reference.\n\n\n\n FIREYE MP-5101\n 3 Manchester Road APRIL 3, 2013\n Derry, New Hampshire 03038 USA Supersedes March 27, 2009\n www.Fireye.com\n\n2"}]