Datasheet Content
[{"filename":"AN_EN_Ed18_April-2024.pdf","text":"PUMP TYPE AN AN\n AN - 11 - Ed 18 - April 2024\nThis is a general specification leaflet; for specific applications not covered herein,\n PUMP\ncontact Suntec.\n IDENTIFICATION\n (Not all model combinations are available\nThe SUNTEC AN oil pump is the basic model incorporating a pressure regulating\n Consult your Suntec representative)\nvalve with cut-off.\n AN : basic valve with cut-off\nCOMPATIBILITY\n V : B100 applications\n- Domestic oil, HVO, B100 (biofuel blend with the addition up to 100% FAME, as\n Gear set capacity\ndefined in DIN SPEC 51603-6 and EN 14214), kerosene. (see pump capacity curves)\n- One or two-pipe system.\n- Normally associated with in-line solenoid valve. Shaft rotation\n and nozzle location\nPUMP OPERATING PRINCIPLE (seen from shaft end)\n A : clockwise rotation /\n right hand nozzle.\nThe gear set draws oil from the tank through the built-in filter and transfers it to the\n B : clockwise rotation /\nvalve that regulates the oil pressure to the nozzle line. left hand nozzle.\nAll oil which does not go through the nozzle line will be by-passed through the valve C : anti clockwise rotation /\n left hand nozzle.\nback to the return line, in a two pipe installation or, if it is a one-pipe installation, back\n D : anti clockwise rotation /\nto the suction port in the gear-set; in that case, the by-pass plug must be removed right hand nozzle.\nfrom the return port, and the return port sealed by steel plug and washer.\n K : Kerosene applications\nThe valve also has a cut-off function as follows:\nDuring starting period when the gear-set speed is increasing, all the oil passes\nthrough a special flat on the piston, back to the return. Once the speed reaches a AN V 47 C K 1 3 xx 6 P\ncertain value and the flow can no longer pass through this flat, then the pressure Pump series\nincreases rapidly overcoming the valve spring force and opens the valve. 1000 : standard\nDuring the stop sequence, the gear-set speed slows down and the valve closes 7000 : with side\n pressure ports\nwhen the gear-set capacity is lower than the flat flow.\n 2 : hub Ø 54 mm\nThe cut-on and cut-off speeds depend on the gear-set size, and set pressure.\n 3 : hub Ø 32 mm\n\n Model number\nBleed\nBleeding in two pipe operation is automatic, but it could be accelerated by loosening Revision number\nthe plug in a pressure gauge port. Installation\nIn one pipe operation, a pressure port must be opened to bleed the system. P : by-pass plug installed in return port\n for two-pipe operation.\n M : without by-pass plug, return plugged\n for one-pipe operation.\n\n\n\n\n Oil under suction Pressure\n adjustment To nozzle\n\n Oil under pressure\n By-passed oil\n returned to tank, Shaft seal\n or to suction Pressure\n gauge port\n Back\n to suction Gear set\n\n\n Vacuum\n gauge port\n\n By-pass By-pass\n plug plug\n removed inserted\n Return\n ONE PIPE TWO PIPE Return Inlet\n plugged\n INSTALLATION INSTALLATION\n\n\n SUNTEC INDUSTRIES FRANCE - 1, rue Lavoisier - CS 60 102 - F-21603 LONGVIC Cedex - www.suntec.fr\n\fTECHNICAL DATA Pump capacity\n Capacity (L/h)\nGeneral\n\n\n\n\n Ref: SK107 - 03/11/98; SK315 - 27/01/07\nMounting Flange or hub according to EN 225\nConnection threads Cylindrical according to ISO 228/1\nInlet and return G 1/4 (with facilities for conical sealing on revision 6\nmodels)\nNozzle outlet G 1/8\nPressure gauge ports G 1/8\nVacuum gauge port G 1/8\nValve function Pressure regulating and cut-off\nStrainer Open area : 6 cm² (AN 47/47K, 57/57K, 67/67K)\n 20 cm² (AN 77/77K, 97/97K)\n Opening size : 150 µm\nShaft Ø 8 mm according to EN 225\nBy-pass plug Inserted in return port for two-pipe system; Pressure (bars)\n\n to be removed with a 4 mm Allen key for one-pipe system Viscosity = 5 cSt - Rated speed = 2850 rpm\n 1,8 cSt\nWeight 1 - 1,3 kg (depending on the model)\n Data shown take into account a wear margin.\n Do not oversize the pump when selecting the gear capacity.\nHydraulic data\nGear size Nozzle pressure range* Factory setting Power consumption\n47/57 7 - 14 bars 9 bars Power (W)\n67/77/97 10 - 20 bars 14 bars\n47K/57K/67K/77K/97K 7 - 15 bars 9 bars\n\n\n\n\n Ref: SK107 - 03/11/98; SK318 - 27/01/07\n* other ranges available on request, refer to the specified range of the particular\nfuel unit.\nOperating viscosity 2 - 75 mm²/s (cSt) for AN 47/57/67/77/97\n 1,25 - 75 mm²/s (cSt) for AN 47K/57K/67K/77K/97K\nOil temperature 0 - 60°C in the pump.\nInlet pressure 2 bars max.\nReturn pressure 2 bars max.\nSuction height 0,45 bars max. vacuum to prevent air separation from oil.\nRated speed 3600 rpm max.\nTorque (@ 45 rpm) 0,10 N.m (AN 47/47K, AN 57/57K)\n 0,12 N.m (AN 67/67K)\n 0,14 N.m (AN 77/77K)\n Pressure (bars)\n 0,20 N.m (AN 97/97K)\n Viscosity = 5 cSt - Rated speed = 2850 rpm\n 1,8 cSt\n\n PUMP DIMENSIONS (in mm)…
